Admin 2013-04-04 at 2:02 pm
Greetings to you, dear readers. Today I will not take away a lot of time and immediately go to the news:
i found two reasons why in the pants sewn by us on the rear halves either bubbles or folds under the buttocks appear. And the second: how to fix the "crochels" on the pages of the replication of my goods (at the end of the article).
When I realized how the degree of removal of the middle suture of the rear half from my figure depends, then the pants began to get on "Hurray!".
It is possible to correct such trouble by adjusting the middle seam of trousers. In order to determine the correction method, you need to analyze your figure and determine the degree of convexity of the buttocks and abdomen.
Today we will analyze the case with flat buttocks. And we will talk about how to adjust the pattern for a protruding abdomen and buttocks.
When building the rear halves of the basic pattern of the trousers, the average seam removal degree must match the magnitude of the back of the back, as in the picture:
If you have found in the fitting that there was an extra freedom (as if a bubble) appeared on the pope, the middle seam behind the body is lagging behind the body, then lay the fold more superfluous and pinched the pins (as in Rice above). The length of the middle seam of the rear halves will decrease and the angle of the average seam will also decrease and will correspond to the figure.
If in the details of the trousers there is a good allowance for the processing of the middle seam, then your pants can still be saved.
For convex buttocks and protruding tumors, it will be necessary to adjust the front, and rear halves. But a little differently. About this in the next article.
pS:very often, I come with letters with complaints about the fact that pages with a description of the goods, where you can make a purchase, course « Side my first pants «, Look "crocameras." I don't really understand why this happens. In one browser opens normally, and suddenly such a "charm". If you encounter such a problem, you can try to fix it yourself: you need to change the settings in your browser. To do this, do 2 steps: click on the View tab, then encoding, then in the right window, click Unicode (UTF-8). Everything.
How to sew trousers in one hour. It's really just to find out how to sew trouserswithout making complex patterns and calculations. This pattern is simple and brilliant and tailoring trousers will not take much time, anything difficult, anyone can sew pants. You will be easy and easy to sew beautiful pants.
Trendy trousers made a revolution in fashion when their famous actress Hollywood Marlene Dietrich was dressed in their time. Pants are beautiful, fresh, romantic, give you beauty and youth, perfectly hide the flaws of the figure. Want beautiful trendy trousers, go on health.
Pants can be sewed not only in cold weather, but also in warm seasons, it all depends on the fabric, we use warm fabric in the cold season, and we use light and cool tissue when heat.
In the cold time, select the material so that the pants keep the shape well and stretched a little, in warm time The year beautiful will look at the flowing fabric.
Beautiful trendy pants, you can sew easily and quickly
How to sew trousers
The pattern of trousers is very simple, no difficult calculations and drawings will be required.
It is necessary to take jeans that are perfectly sitting and look good at you, we apply jeans to the material and Crow on them.
It will take material with a slight content of Elastane.
Pants glue look perfectly, make the arrows on the pants and give the slightness of your figure.
However, it can be experimenting with this pattern, because the pants can not only expand to the bottom, but also to make straight, or to seas, depending on which style you goes. Experimentably boldly, you can raise or omit in the waist, you can change the belt and belts, everything is in your hands.
Below is the video from which you will learn how to sew trousers, can easily sew shorts and breeches.
Enjoy your sewing.
For sewing trousers we will need:
- 150 cm of woolen fabric with the addition of elastane less than 5% (width 140-150 cm);
- zipper 15-18 cm;
- threads suitable for fabric color;
- adhesive Flizelin.
Pattern female trousers We will not need - enough to take our favorite jeans that are well sitting on you. So, decay the fabric. It should be folded twice as the front side. We apply your jeans to it, folded back outward.
Blacks Rest Detail Trousers
We begin to circle the rear half of the trouser through the seat line.
We make a hurry on every detail of the trouser
At the waist level, approximately in the middle, we will cover a 3 cm wide width and we spoil the resulting fold pin. The hopper is needed for better fit trousers in the figure.
Black sutim
Blacks of waist line, hips line. Little pants a little book. To do this, use a ruler. We carry out a line of PO inner side Trousers and celebrate the line of Niza. Rear half trousers ready!
Black Seat line
Similarly, we build the front of the trousers. Please note: the front of the trousers is always less than the rear. Jeans fold the front out and apply to the fabric. We start with the seat line.
We make a hint of 3 cm wide
We make a copy of the width3 cm, temper it and supply the waist line.
Diameters lateral line
Using a ruler, spend the side line of trousers. We supply the internal (step) seam and the line of Niza.
Cut the parts with letters on the seams
Cut the details, retreating from the drawn lines by 1-1.5 cm (inserts on the seams). We get 4 details of future trousers: two details of the transfer and two rear parts.
Blacks fuck
In those places where the covers were left, shafts of the cuttings. In the middle of the upset, we carry out a line of 8 cm long and put the point. We connect the edges of the relentment with this point so that the triangle is turned out. All the extortes must be four: one on every detail.
Sewing the swallow
We fold the molds along the drawn lines and stitch on the machine. At the time of stitching, the facial side of the fabric should be inside.
We sew the details together
We sew the stepper seams together (those that go along the inside), side seams, applying the back item to the front face inside. Let's leave a zipper. To do this, one of the side seams will begin to process, retreating down from the waist line by 15 cm. All sections of the fabric are processing on overlock or on a conventional typewriter using a zigzag seam and irrigate.
Sewing zipper
We sew zipper.
Measure the width of the waist
We measure the width of the trousers along the waist line.
Cut the belt belt
We proceed to the exhibition of the belt. Its length should be on 3-4 casual widths just measured line. Such a length is needed for a button or hook.
Sew belt to pants
In order for the belly of the trousers not to lose the form and did not stretch, we clarify his strip Fliselin. You can cut a strip from a piece of adhesive material or buy a special fliseline with a perforated edge. We apply it with the adhesive side to the wrong piece of the belt and stroke not very hot iron. You can iron through the gauze. Send the belt, folding the part side of each other. The opposite side of the belt is processed by zigzag or overlock. The belt turns away, fold, weep and sew at a distance of 1-2 mm from the edge. We make a loop for a button or sew a special trouser hook.
Subscribe to news in the upper right corner of the site, and you will always be aware of the newest sewing and repair. You will be the first to know about the new articles of sewing secrets and cutting clothes. The news of the new article will immediately come to you.
Dear friends, if you like this page, or site, please, please review in the comments. And tell your friends. Leave messages in the comments Share your thoughts about the article or site. I will be very grateful to you.
Sincerely, Olga Rubtsova.
To build the front of the trousers, download the pattern and start the preparation of the pattern on paper. Build a straight corner with a vertex at the point T..
Length trousers . From the point T. down to postpone the measure of the length of the product and put the point N.: Tn. = DI \u003d 102 cm.
Niza line. From the point N. Right to spend a straight line of arbitrary length, perpendicular to the line Tn..
Seat depth . From the point T. down to postpone 1/2 measurements plus 1 cm and put a point B.: TB = Pok./ 2 + 1cm. \u003d 52/2 + 1 \u003d 27cm.
Width trousers . From the point B. To the right to postpone 1/2 measurements Pok. p l yus 0.5 cm and put a point B1. :BB1 = Pok./ 2 + 0.5 cm. \u003d 52/2 + 0.5 \u003d 26.5 cm.
Seat width. From the point B1. to the right to postpone 1/10 measurements of the semi-rapid thighs and put the point B2.: B1B2. = Pok./ 10 \u003d 52/10 \u003d 5.2 cm.
From the point B., up spend a straight parallel TB, up to the waist line and put a point T1.. From the point B1. up to postpone the segment equal B1B2., i.e. 5.2 cm. Points 5,2, B2. Connect the smooth line as shown in the drawing.
Snow line. Seat width (cut B1B2.) To divide in half. Cut from the division point to the point B. split in half and put a point B3.. From the point B3. Down to line niza and up to the waist line to hold a dotted line, parallel lines Tn..
Width of the niza trousers. From the point N. to the right to postpone 4-6 cm. Points 4-6, B. Connect. From the line of oguli to the right to postpone the segment equal to the segment from the point 4-6 up to the line of snowy, and put a point H1. (The equality of segments in the drawing is indicated by two dashes). Points H1. and B2. Connect.
Registration line of waist trousers. From the point T1. Down to postpone 1 cm. Points 1, T. Patterns need to be connected.
Calculation of the depth of the Talio Pulling. Measure line T1B1:
T1B1\u003d 26.5 cm.
From the value obtained, take 1/2 measurement of the waist semi-ray: 26.6 cm. SWEAT/ 2 \u003d 26.5- 38/2 \u003d 7.5 cm.
The resulting difference is minus 0.5 cm (landing) to distribute on lateral and front dye: 7.5-0.5 \u003d 7 cm, 7cm. / 2 \u003d 3.5 cm.
Registration of side extract. From the point T. To the right along the waist line to postpone 3.5 cm. Embossed a flushing line, as shown in the drawing. The design of the front folding (folds). From the line of ostuguchi to the right and to the left to postpone half the cuttings:
3.5 / 2 \u003d 1.75 cm.
The contour lines of the front of the trousers pass at the points: 3.5, b, 4-6, n1 b2, 5,2, 1,3,5.
So you made the pattern of the front of the trousers.
Build pattern of the back of the trousers.
Follow the step-by-step intrustors for beginners. Caring basic pattern You can sew any pants yourself.
Seat width. From the point B2. To the right to postpone 1/10 measure Pok. Plus 3 cm and put a point B4.:
B2B4. \u003d CC / 10 + 3 cm. \u003d 52/10 +3 \u003d 8.2 cm.
Determination of the seat of the back of the pants.
Section B2B4. split in half.
From the point of dividing down to postpone 1 cm. From point T1 left along the waist line to postpone 1/10 Measured of the High seaside and put the point T: T1T= Pok./ 10 + 52/10 \u003d 5.2 cm.
Points 5,2, t connect, continuing the line up on 1/10 measurement of the semi-rapid thighs, and put the point t1. :
tT1 = Pok./ 10 \u003d 52 // 10 \u003d 5.2 cm.
Pick up suitable model Pants skirts for any female figure. The convenience of the style and the ability to combine the product with other objects of clothing, practicality and attractiveness make this thing popular in various life situations. For sewing, the trouser skirt will require a desire to create a unique thing and the initial sewing skills.
How to cut the skirt pants
The pattern of the trouser skirt can be built on the basis of the pattern of classic trousers, adding rolds with folds or expanding the book.
In specialized editions on sewing there are ready-made patterns of any styles. When using ready-made patterns, sewing takes less time, but they have to be customized under the features of the shape. When the parts are transferred to the fabric and the depth section, the pattern is stirred in the direction of the equity thread.
In flow calculations, take into account the width of the material. Narrow tissue with a width of 0.8-1 m will need a quantity equal to 3 lengths of the finished product, taking into account 8 cm on the seams. Material 1.4 M wide need 2 lengths of the finished product with a residancy 4 cm on the seams.
If folds are provided in the model, both panels are cut in the middle. Then both parts are moved to 16 cm if 2 folds are planned or 24 cm when performing three.
At the bottom of the product, the fold width is reduced by 3 cm on both ends, then combine the obtained points on the lower cut of the product with the folding points with the thighs line. If the sewing of the finished product is planned from thick fabric, then some folds to the thigh are cut.
When skirt trousers, the upper plots are prolonged to the hips.
How to sew skirt trousers on elastic
A feature of the pattern of the finished product on the rubber band will be the absence of extracts at the level of the waist and the presence of a single belt. Such models are universal when landing on any shape.
Start working from crosslinking internal and side seams, machines are processed and squeezed. Then the model is stitched over the step slice, process allowances. The outlet detail of the belt is folded in the middle and estimated. It is addicted to the product, leaving a unpripted segment through which the gum will be inserted.
A wide gum is inhibited into a belt through the provideding hole, its edges are stitched. Then drain the hole and processed the bottom of the product.
How to sew a skirt pants without pattern
Simple model skirt trousers can be built directly on the fabric.
Sequencing:
- Cutting the tissue you need to roll 2 times and cut two rectangles of the following dimensions: one side must match the length of the finished product, increased by 20 cm for the waist cutout, the second side is greater than the first 2 times. Then the detail is folded in half.
- For the hole of the waist, a semicircle is cut into place of folding rectangle. Its length is calculated based on the volume of the waist, divided by 4, with a premium from 5 to 10 cm. On one part, the left angle is cut onto another - right.
- To obtain a nose product, the angle opposite to the waist cut is cut off by a semicircle.
- Next, a stepper cut is cut from 25 to 30 cm deep, from 5 to 10 cm wide.
- First cross inner cut. On the rear cloth drain the wrappers on the waist.
- Then they become a stepper cut, in front of the front sew zipper.
- Send the belt and handle the bottom of the product.
How to sew a skirt-pants with your own hands - video
Beginner craftsmen will be useful to see a few videos about stripping and sewing products.
How do pants skirt
With the help of a trouser skirt, you can create any image: business, romantic, sexy. Summer combination is possible with T-shirts, shirts, tops and jerseys.
At the cold season, they sew a model of warm tissues, combine it with light sweaters, fitted jackets, turtlenecks. Upper clothes Choose a short-butted: you can use fur seashes to hips, shortened coat models. When creating an image, it is worth remembering that the trousers skirt has a significant amount that is equilibrated by the fitting riding.
You can complete the image with various accessories: cervical scarves, massive bracelets, necklaces, beads of several threads. For products on the belt, we choose wide straps with decorative buckles.
Emphasize the spectacular thing is possible with shoes, sandals or heel shocks. High-top boots are better not to wear in combination with trousers skirt. For everyday wearing, the boats without a heel or ballet shoes are chosen.
Very fashionable is a bright long model of a trouser skirt, made of light flowing tissues, which looks outwardly not like pants.
Special cut models are visible only when moving. This allows you to hide the flaws of almost any figure.
Hello, my dear readers' site blog. Now we will be sew trendy trouserswith a lowered seating line and 7/8 length.
This below is the finished pattern for downloading is designed for such dimensions:
- Art \u003d 38.
- Sat \u003d 50.
- Height to the knee from the waist \u003d 56
- Half cranks \u003d 22
- Width of the trouser at the bottom \u003d 33 cm. (On narrow caviar)
- Pants length 93 cm.
If you approach the hips, you can adjust the remaining measurements.
Later I will tell you how to build the pattern of trousers step by step.
Download the pattern and cut the details from the fabric. I sew from the costume of non-stretch tissue. You can take any costume or denim, according to your desire.
Cut the details of your pocket and slopes (it will need to be built using the pattern of Gulfi). Consider this moment a little later.
We connect both halves of trousers (front and rear) from knee control point First up, then down. We fasten the pins or take.
We sew on the typewriter both halves of trousers. This is what should happen:
Now we treat the bottom of the trousers. Initially, I laid 2 cm points at the bottom, so that 1 cm could be twice. We compose first by 1 cm bottom trousers. Wallowing this place.
Then we put another 1 cm. Welts.
Once again weeping the finished bottom of the trousers.
Now you need to handle zipper in pants and make a belt.
Send the belt to the trousers on the typewriter.
Soak the belt so that both of its parts (external and internal) were face to face. Now you need to sew the side sides of the belt so that they smoothly go to Gulfik. We take and flash the side sides of the belt along the battery line. (as in the photo on the right)
Now we will undermine the allowances on the side of the belt and we bring the internal belt's allowances so that it is slightly close to the inner belt of the suture of the belt to trousers. It is advisable to turn this seam by 2 mm, then the neat inside of the belt will be.
Now important moment. We flash from the front side in the suture of the belt belt to the pants. Thus, we enjoy the inner belt to external, and all the allowances will remain inside, and there will be a beautiful internal treatment of trousers.
It is only very important to accurately fall into this seam. To do this, push (as if we stretch) in different directions the belt and the pants themselves. Then we will iron the belt and this stitch will not be visible if you do everything neatly.
But the belt lacks the loan, where we can hang the belt.
Now it's time to make a loop and sew a button on trousers.
To do this, we use a special paw for loops. We insert our button in the paw, put the paw in the machine. Do not forget to lower a special thing down, so that it stops the course of the machine and directed in the opposite direction.
The typewriter has a special loop mode, as in the photo below.
And of course, do not make a loop immediately on trousers, and practice first several times on the same fabric with which you sew pants. Since the loop may need to be corrected.
Made a loop on trousers.
And sewed a button.
P.S. Although I built them on myself, I wanted them to be with an understated seam (I lowered the line of seating by 5 cm from natural), but in ready product This turned out to be too much. Perhaps it depends on the quality and density of the tissue. In any case, you will be able to adjust this moment if necessary (to rinsely from the inside).
See also video about how to sew new pants without pattern, taking favorite old pants:
I hope the article I went to your heart and if you sewed the trousers - they will bring you many joyful moments !! Shave with me!
